#include <IRremote.h>

int RECV_PIN = 11; // Pin vom IR-Empfänger
int LED1 = 2; // LED Pin
int LED2 = 3; // LED Pin
int LED3 = 4; // LED Pin
int LED4 = 5; // LED Pin
int LED5 = 6; // LED Pin
int LED6 = 7; // LED Pin

// Ab hier können Sie die Tastenbelegung anpassen
long on1 = 0x00FFA25D;
long off1 = 0x00FFE01F;
long on2 = 0x00FF629D;
long off2 = 0x00FFA857;
long on3 = 0x00FFE21D;
long off3 = 0x00FF906F;
long on4 = 0x00FF22DD;
long off4 = 0x00FF6897;
long on5 = 0x00FF02FD;
long off5 = 0x00FF9867;
long on6 = 0x00FFC23D;
long off6 = 0x00FFB04F;

IRrecv irrecv(RECV_PIN);
decode_results results;

// Dumps out the decode_results structure.
// Call this after IRrecv::decode()
// void * to work around compiler issue
//void dump(void *v) {
// decode_results *results = (decode_results *)v
void dump(decode_results *results) {
  int count = results->rawlen;
  if (results->decode_type == UNKNOWN) {
    Serial.println("Could not decode message");
  } else {
    if (results->decode_type == NEC) {
      Serial.print("Decoded NEC: ");
    } else if (results->decode_type == SONY) {
      Serial.print("Decoded SONY: ");
    } else if (results->decode_type == RC5) {
      Serial.print("Decoded RC5: ");
    } else if (results->decode_type == RC6) {
      Serial.print("Decoded RC6: ");
    }
    Serial.print(results->value, HEX);
    Serial.print(" (");
    Serial.print(results->bits, DEC);
    Serial.println(" bits)");
  }
  
  Serial.print("Raw (");
  Serial.print(count, DEC);
  Serial.print("): ");

  for (int i = 0; i < count; i++) {
    if ((i % 2) == 1) {
      Serial.print(results->rawbuf[i]*USECPERTICK, DEC);
    } else {
      Serial.print(-(int)results->rawbuf[i]*USECPERTICK, DEC);
    }
    Serial.print(" ");
  }
  Serial.println("");
}

void setup() {
  pinMode(RECV_PIN, INPUT);
  pinMode(LED1, OUTPUT);
  pinMode(LED2, OUTPUT);
  pinMode(LED3, OUTPUT);
  pinMode(LED4, OUTPUT);
  pinMode(LED5, OUTPUT);
  pinMode(LED6, OUTPUT);
  pinMode(13, OUTPUT);
  Serial.begin(9600);

  irrecv.enableIRIn(); // Start the receiver
}

int on = 0;
unsigned long last = millis();

void loop() {
  if (irrecv.decode(&results)) {
    // If it's been at least 1/4 second since the last
    // IR received, toggle the relay
    if (millis() - last > 250) {
      on = !on;
      // digitalWrite(8, on ? HIGH : LOW);
      digitalWrite(13, on ? HIGH : LOW);
      dump(&results);
    }
    if (results.value == on1)
      digitalWrite(LED1, HIGH);
    if (results.value == off1)
      digitalWrite(LED1, LOW);
    if (results.value == on2)
      digitalWrite(LED2, HIGH);
    if (results.value == off2)
      digitalWrite(LED2, LOW);
    if (results.value == on3)
      digitalWrite(LED3, HIGH);
    if (results.value == off3)
      digitalWrite(LED3, LOW);
    if (results.value == on4)
      digitalWrite(LED4, HIGH);
    if (results.value == off4)
      digitalWrite(LED4, LOW);
    if (results.value == on5)
      digitalWrite(LED5, HIGH);
    if (results.value == off5)
      digitalWrite(LED5, LOW);
    if (results.value == on6)
      digitalWrite(LED6, HIGH);
    if (results.value == off6)
      digitalWrite(LED6, LOW);
    last = millis();
    irrecv.resume(); // Receive the next value
  }
}